The 200 A / 2000 A current clamp with BNC connector allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires. Simply clamp the jaws around the cable to be tested and plug the clamp into your PicoScope. Before the launch of this probe we recommended the TA019 (600 A) for working on the starting and..

The TA018 current clamp with BNC adaptor is ideal for use with PicoScope automotive oscilloscopes for measuring currents between 10 mA and 60 A. This enables the PicoScope to display current waveforms for fuel injectors and fuel pumps. The current clamp has two calibration settings, set by a slider switch on the handle of the probe. 1 mV/10 m..

The TA019 current clamp with BNC connector is ideal for use with a PicoScope automotive oscilloscope to display starter current waveforms, charging currents and for performing quick compression tests. The current clamp can measure up to 600 A (AC or DC). In use there is no need to break into the circuit or disturb the isolation as the ..

Flexible Coil on plug inductive probe including BNC to BNC lead with ground The PP357 coil-on-plug (COP) and signal probe from Pico Technology is the fastest way to check coil-on-plug ignition coils and spark plugs. Find misfires fast Displays scope patterns of the secondary, faster than scoping the primary Works on all automotive scop..

You’ve got the best oscilloscope, now get the best leads These premium leads are colour–coded so that the colour of the lead in the engine bay matches the colour of the on–screen waveform in PicoScope Automotive — never again will you waste your time wondering which lead is what. Our premium leads are fully s..

The 30 A precision current clamp with BNC connection allows you to measure from 5 mA up to 30 A without cutting, disconnecting or stripping the wire. It is ideal for measuring the currents in sensors and actuators across most modern passenger and commercial vehicles. The TA189 provides improved sensitivity, lower noise and faster response. Featu..

The PicoBNC+® equipped TA496 is a natural choice if you are a PicoScope 4225A and 4425A user looking to add a compact low amps clamp to your PicoScope probe collection. The PicoBNC+® 60 A DC compact current clamp’s reduced form factor fits comfortably in your hand and improves accessibility in tight and difficult to access test loc..

Coil on Plug extension lead Set of 4. Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there ..

Coil on plug extension lead (Single) Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there i..

Pico Secondary ignition pickup lead - capacitive with BNC (MI074) Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection. Attempting to make a direct connection will almost certainly damage the measuring instrument. The MI074 is a capacitive pickup that simply connects aro..

2 x WPS600c in carry case. With high accuracy and a wide measuring range, the WPS600C Hydraulic Pressure Transducer connects to your PicoScope for convenient analysis and diagnosis of pressurized systems. Accurately measure up to 600 bar (8700 psi) Ultra-fast 100 microsecond response time (0% to 90% of full scale) Internal rechargeable..

Traditional pressure gauges do not provide technicians with a graphical representation of their measurements so they can’t show and/or record the pressure values and trends they observe during the test. As such, they can’t easily share their results with customers, colleagues or technical support and warranty teams. Nor can they come ba..

Pico Technology Ultrasonic Parking Sensor Detector (***To be used as an accessory with Pico automotive oscilloscope. Pico automotive oscilloscope supplied separately.***) This 2 meter long lead and detector is intended to allow a technician to prove the correct operation of each of the ultrasonic parking sensors in turn. By directly showing the ..

The TA330 is a detector intended to allow a technician to detect the presence of the keyless entry carrier frequency in the range 125 to 140 kHz (as used by most manufacturers). The device has a short range by design, allowing the technician to check each pickup coil in turn and hence identify a faulty unit. The detector does not pick up or de..

The TA466 is a standalone tester that is used to check for the presence or absence of a voltage, and thereby allows the technician to confirm that the high-voltage has been disconnected from a circuit before proceeding. The measurement range is up to 690 V AC and 950 V DC to suit electric and hybrid vehicles, and the unit features a 3-digit red and..