Pico 0-2000 BNC Amp Current Clamp

$452.10 incl. GST

Brand: Pico Technology

Product Code: TA167

Availability: In Stock

Viewed 20896 times

Qty

Add to wishlist
Add to compare

Categories Cart Account Search Recent View

Instructions

Switch on
When the probe is switched on to the required measuring range, the green LED will illuminate. The LED starts flashing when the battery voltage is too low for normal operation and warns you that it requires changing. This procedure is described below.

Auto power off
In order to save battery life, the probe will automatically switch itself off after approximately 10 minutes. To disable the auto power off function, switch off the probe and switch on while pressing the auto zero button. The red LED will illuminate and the probe will stay on until switched off again.

Auto zero
The output zero offset voltage of the probe may change due to thermal shifts and other environmental conditions. Select the required measuring range and to null the output voltage
depress the Auto Zero button. Ensure that the probe is away from the current-carrying conductor while the probe is being nulled.

Current measurement
1. Switch on the probe by selecting the required measuring range and check that the green LED is lit.
2. Connect the output lead to the oscilloscope,
3. Zero the probe using the Auto Zero button.
4. Clamp the jaws of the probe round the conductor ensuring a good contact between the closing faces of the jaws.
5. Observe and take measurements as required. Positive output indicates that the current flow is in the direction shown by the arrow on the probe.

Battery replacement
The green or red LED will flash when the minimum operating voltage is approached. Use the following procedure:

SAFETY WARNING
Before removing the battery cover, ensure that the probe is disconnected from the oscilloscope and remote from any live electrical circuit.

Unclamp the probe from the conductor, turn it off using the On / Off switch and disconnect the output leads from external equipment. Loosen the captive screw that secures the battery cover. Lift the cover through 30° and pull it clear of the probe body. Replace the battery, re-fit the battery cover and fasten the screw.

Fit only Type 9 V PP3 Alkaline (MN 1604).

Example waveform using current clamp to perform a relative compression test on a diesel engine.

Electrical data
(All accuracies stated at 23°C ± 1°C)
Nominal current	2000 A AC pk max. or DC
Measuring range(s)	2000 A
Overload capacity	2200 A (60 s)
Output sensitivity	10 mV/A and 1 mV/A switchable
Accuracy1) (0 to 200 A of 10 mV/A)	± 1% of reading ± 100 mA
Accuracy1) (0 to 1500 A of 1 mV/A)	± 1% of reading ± 500 mA
Accuracy1) (1500 to 2000 A of 1 mV/A)	± 4% of reading
Gain variation	±0.15% of reading/°C
Frequency range	DC to 20 kHz (–1 dB)
	iRMS x f ≤ 400,000
Power supply	9 V alkaline battery PP3, MN 1604 or IEC6LR61
Load impedance (minimum)	> 100 kΩ and ≤ 100 pF

General data
Conductor size	32 mm diameter
Output cable and connectors	2 m long coax terminated with safety BNC connector
Operating temperature	0°C to +50°C
Storage temperature with Battery removed	–20°C to +85°C

1)Accuracy quoted is for conductor in centre of aperture

Product Description

The 200 A / 2000 A current clamp with BNC connector allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires. Simply clamp the jaws around the cable to be tested and plug the clamp into your PicoScope.

Before the launch of this probe we recommended the TA019 (600 A) for working on the starting and charging systems of petrol passenger cars and the PP253 (2000 A) clamp for high compression diesel engines. The TA167 (200 A / 2000 A) covers both these applications in one probe with improved range and sensitivity, lower noise and faster response.

The TA167 features a 200 A mode for better performance at lower currents and has an increased jaw size. It also features an auto power-down facility to save battery life when not in use (this feature can be disabled for battery drain / shutdown current testing).