Pico Technology Ultrasonic Parking Sensor Detector (***To be used as an accessory with Pico automotive oscilloscope. Pico automotive oscilloscope supplied separately.***) This 2 meter long lead and detector is intended to allow a technician to prove the correct operation of each of the ultrasonic parking sensors in turn. By directly showing the ..

The TA330 is a detector intended to allow a technician to detect the presence of the keyless entry carrier frequency in the range 125 to 140 kHz (as used by most manufacturers). The device has a short range by design, allowing the technician to check each pickup coil in turn and hence identify a faulty unit. The detector does not pick up or de..

The TA466 is a standalone tester that is used to check for the presence or absence of a voltage, and thereby allows the technician to confirm that the high-voltage has been disconnected from a circuit before proceeding. The measurement range is up to 690 V AC and 950 V DC to suit electric and hybrid vehicles, and the unit features a 3-digit red and..

The TA467 Insulation tester is specially designed for vehicles with on-board high voltages and conforms to EN61010 CAT III (1000 volts) and CAT IV (600 volts). The insulation test function allows testing of the insulation of the high voltage wires found on high-voltage vehicles. It can be used as a stand-alone device or linked wirelessly with the s..

The TA487 is an interface that allows industry-standard IEPE (integrated electronic piezoelectric) sensors to be used with any oscilloscope or data acquisition device with BNC inputs. The device is powered from any USB port, using the cable supplied, and provides a 4mA constant current source to power a connected IEPE sensor. A TA095 IEPE a..

Field repairable back pinning and piercing probe set, with very small diameter, very sharp pins. ..

Convert your oscilloscope accessories with 4mm adaptor to BNC connection. The BNC to 4mm adaptor connects two 4mm (banana) plugs to a BNC socket. The 4mm sockets and BNC plug are fully shrouded for safety...

This high-quality general purpose oscilloscope probe has a 60 MHz bandwidth. A two-position slide switch allows attenuation of either x1 or x10 to be selected. This probe is particularly useful if you want to probe higher speed automotive CAN bus and FlexRay signals using the Pico oscilloscope...

Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and ..

  J Case fuse extension lead The TA168 JCASE fuse extension lead is designed to be used with standard and low profile JCASE fuses. JCASE is a cartridge style fuse with female terminal design, providing both increased time delay and low voltage drop to protect high current circuits & handle inrush currents.  ..

Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and ..

Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and ..

The TA206 maxi fuse extension lead is designed to be used with standard maxi automotive fuses. The maxi fuse is a large blade-style fuse used to protect high-current circuits and handle large inrush currents on some vehicles...

TA191 Breakout Lead 3 pin Kostal..

With high bandwidth and fault protection, the 10:1 attenuator allows you to measure fuel injector and primary ignition waveforms using PicoScope oscilloscopes. The TA197 is a passive 10:1 attenuator. This means that, for example, a 10 V signal at its input appears as a 1 V signal on its output. It allows voltages of up to 400..